How to use Infinix Flash Tool I am thrilled to introduce you to my experience with the Infinix Flash Tool, a more user-friendly option compared to the SP Flash tool. Before you begin, ensure that you have your firmware (ROM) ready and have installed the MediaTek USB VCOM drivers as the tool will not recognize your phone without them. In this guide, I will walk you through the steps of installing the drivers, loading your firmware, and flashing your Infinix device. It is crucial to not interrupt the flashing process to avoid any potential issues with your phone. By following my instructions, you will successfully flash your device and have it running smoothly once again.
Table of Contents
How to Prepare for Flashing
While preparing to use the Infinix Flash Tool, there are a few vital steps you need to take to ensure a successful flashing process.
Obtaining the Necessary Files
Some of the necessary files you’ll need to have ready include the ROM (firmware) you wish to flash, which should be extracted beforehand. Make sure you have all the required files in place before proceeding.
Installing Mediatek USB VCOM Drivers
With the necessary files in place, the next step is to install the Mediatek USB VCOM drivers. Without these drivers, the Infinix Flash Tool will not be able to detect your phone.
It’s crucial to install the correct driver for your PC’s specs. You’ll need to navigate to the location of your Mediatek VCOM driver and select the folder according to your PC’s operating system (32-bit or 64-bit). If you encounter a prompt warning that the driver is not signed, click “Yes” to proceed. This step is critical, as the driver installation will enable the tool to detect your phone.
Be cautious when installing the drivers, as incorrect installation may lead to errors. Once the drivers are installed, you’ll see the “Mediatek DA USB VCOM Port” in your device manager, indicating that the installation was successful.
Tips for a Smooth Flashing Process
Clearly, flashing your Infinix device requires some preparation and attention to detail to avoid any potential issues. Here are some tips to ensure a smooth flashing process:
- Install Mediatek USB VCOM drivers before proceeding with the flashing process.
- Make sure your phone is switched off before connecting it to the PC via USB cord.
- Avoid interrupting the flashing process to prevent any potential damage to your device.
- If your phone gets stuck at the boot logo after flashing, try removing the battery (if removable) or booting into recovery mode and performing a factory reset.
Any failure to follow these tips may result in unwanted consequences, so be sure to follow them carefully.
Launching the Infinix Flash Tool
The first step in the flashing process is to launch the Infinix Flash Tool. I right-click on the tool’s executable file and run it as Administrator, waiting for the tool to load.
Loading the Firmware File
The next step is to load the firmware file into the Infinix Flash Tool. I click the Browser button and navigate to the location of the firmware file I wish to flash, selecting the scatter file and clicking Open.
Process of loading the firmware file is crucial, as it contains the necessary instructions for the flashing process. I make sure to select the correct firmware file for my device to avoid any potential issues.
Factors to Consider During Flashing
Despite the simplicity of the Infinix Flash Tool, there are certain factors you need to consider during the flashing process to avoid any potential risks or errors. Here are some key factors to keep in mind:
- VCOM drivers installation: Ensure that you have installed the Mediatek VCOM drivers correctly, as the tool will not detect your phone without them.
- Phone switch-off: Make sure your phone is completely switched off before connecting it to the PC for flashing.
- Correct firmware selection: Select the correct firmware (ROM) for your phone model to avoid bricking your device.
- No interruptions: Do not interrupt the flashing process, as this can cause serious damage to your phone.
Thou shall be cautious and patient during the flashing process to avoid any potential risks.
Switching Off Your Phone
If you’re about to flash your phone, make sure it’s completely switched off. Do not connect it to the PC while it’s still on, as this can cause errors or even damage your phone.
How Connecting Your Phone to the PC
Flashing requires a secure connection between your phone and PC. Ensure that you connect your switched-off phone to the PC via the USB cord, and the flashing process should begin.
With the correct VCOM drivers installed, your phone should be detected by the Infinix Flash Tool, and the flashing process should start automatically. Remember to be patient and not interrupt the process, as this can cause serious damage to your phone.
To wrap up
Conclusively, I believe that using the Infinix Flash Tool is a relatively straightforward process once you have the necessary drivers and firmware in place. I’ve walked you through the steps to install the Mediatek USB VCOM drivers, launch the tool, load your firmware, and flash your phone. Remember to be patient and not interrupt the flashing process, and if you encounter any issues, try booting into recovery mode and doing a factory reset. With these simple steps, you should be able to successfully flash your Infinix phone.